Model NO.: WC67Y-100*2500
Origin: Shandong, China
1. The properties and characteristics of the machineThis machine is used for bending of all kinds of metal materials, such as the selection of the proper mold, but bending cross section shape of the example shown in figure below. This machine is available for aircraft, ships, automobiles, locomotives, packaging, instrumentation, electrical appliances, such as radio factory.
This machine is a hydraulic lift, work by the end of the slider position arrangement in the mechanical stop control inside the cylinder, the slider moves are controlled by distorting synchronous mechanism
Behind the machine mechanical stop and equipped with counter displays, use convenient, intuitive, native sample can realize rapid decline, slow down pressure, pressure, fast return procedures, convenient and reliable work.
Synchronization, so that the work accuracy and repeat positioning accuracy is higher, the partial load resistance is better. Mould with fine-tuning mechanism, can easily adjust the height of each part of upper die position, ensure the bending model with uniform clearance between up and down at work, can significantly improve the bending Angle, precision.
Bending stress according to the thickness, the lower die opening size, the folding sheet metal width, by in sheet metal bending pressure gauge to check the required bending force.
2. The structure of the machine
This machine adopts hydraulic drive, the lathe bed, slider, mechanical stop, after the stopper, the former stackers, hydraulic system, mold, electrical parts, etc.
Machine body
Is welded by the left column, right column, fuel tanks and worktable.
The slider and the mechanical stop
Sliding block connected to the cylinder, oil cylinder is fixed on the left column. Piston push slider movement in different thickness and different Angle of sheet metal, in order to ensure the bending precision, slider has stopped at any selected position accurately, therefore, set up a mechanical stop in cylinder block.
In order to ensure the good quality of bending, two block is highly position must be the same, the machine has been adjusted before they go out, don't want disorderly adjustment as far as possible, lest cause accident if use of the system caused by both sides stop position different slider tilt, hex pipe moves to the right, make the clutch set off, turning on the left side of the worm shaft guarantee after the second block of contour closed hexagon set again
3. Machine technical documents
3.1.Operation ManualÂ
3.2.certificate of conformity
3.3.Packing list (including accessories)
3.4.Machine tool color is the company standard color (red and black), can be customized according to user requirements
4. Machine tool main parameters:
No. | Specifications | WC67Y-100*2500 | Units | Remark | |||
1 | Nominal pressure | 1000 | KN | ||||
2 | Table length | 2500 | 3200 | 4000 | mm | ||
3 | Dis. between columns | 2020 | 2520 | 3100 | mm | ||
4 | Throat depth | 320 | mm | ||||
5 | Slide stroke | 120 | mm | ||||
6 | Adjustment of ram stroke | 120 | mm | ||||
7 | The biggest opening height between worktable and slide | 370 | mm | ||||
8 | Slide speed | Empty load | 60 | mm/s | |||
Full load | 10 | mm/s | |||||
Return | 40 | mm/s | |||||
9 | Main motor | Model | Y160M-4 B35 | B35 | |||
Power | 7.5 | KW | |||||
Rotate speed | 970 | r/min | |||||
10 | Oil pump | Model | NB2-G16F | ||||
Pressure | 31.5 | mpu | |||||
Flow quantity | 16 | L/min | |||||
11 | Overall dimension | Length | 2600 | 3300 | 4100 | mm | |
Width | 1450 | 1480 | 1480 | mm | |||
Height | 2380 | 2400 | 2400 | mm |
Thermal Management System,Electric Water Pump Controller,Brushless Motor Electric Water Pump,Electric Water Pump New Energy Vehicle
Fuxin Dare Automotive Parts Co., Ltd. (DARE AUTO) , https://www.darepump.com